Alarm SAF RMBE Series Bedienerhandbuch PDF herunterladen (Seite 13)

5.1.2.1.2 SPS4 Jumper Settings

The SPS4 has two jumpers for setting its output voltage. It is factory set for 12VDC out. If

a different voltage is required, the jumpers must be changed as follows:

LeftRight5-18VDC Adjustable*

RightLeft12VDC

LeftLeft5VDC

JP2JP1Voltage Output

* - When using the adjustable range, adjust the output voltage using potentiomer R5

5.2 Visual Indicators

5.2.1 External Visual Indicators

5.2.1.1 Illuminated Power Switch / Circuit Breaker

The power switch will illuminate red when the power switch is in the “on” position and power

is present.

5.2.1.2 Front Panel Indicators

All units have front panel indicator LEDs. Each output has one LED which illuminates when

voltage is available at the corresponding output terminals.

F17

D1 D2 D3 D4 D5

D6 D7 D8 D9 D10 D11 D12 D13

D14

D15

D16

F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 F13

F14

F15

F16

JP1 JP2 JP3 JP4 JP5 JP6 JP7 JP8 JP9 JP10 JP11 JP12 JP13 JP14 J P15 JP16

32V

SPARE

38-124 Rev B

ZONES 9 - 16ZONES 1 - 8

FOR CONTINUED PROTECTION AGAINST RISK OF FIRE

REPLACE ONLY WITH SAME TYPE 3A. 32V FUSE.

UTILISER UN FUSIBLE DE RECHANGE

DE MEME TYPE 3 A 32 V

REFER TO NAMEPLATE LABEL

FOR INSTALLATION DOCUMENT

REFERENCE NUMBER

DISCONNECT SUPPLY CORD BEFORE

CHANGING FUSE

DE'BRANCHER AVANT DE REMPLACER LE FUSIBLE

ATTENTION:CAUTION:

Visual Indicators (D1-D16)

5.2.2 Internal Visual Indicators

5.2.2.1 Indicators on the internal PS5-M Board

The PS5-M contains five visual status indicators.

Lights under an Earth Ground Fault conditionYellowEarth Ground FaultGND FLT (D23)

See Section 5.2.2.1.4YellowCommon FaultCOM FLT (D16)

Lights when the AC input voltage is low or missingYellowAC FaultAC FLT (D22)

Lights when DC voltage is present on the outputGreenDC OutputDC OUT (D15)

Lights when AC voltage is present on the inputGreenAC PowerAC ON (D19)

ConditionsColorDescriptionLED

5.2.2.1.1 AC ON

For safety reasons, this LED illuminates any time there is AC voltage present at the AC

input, regardless of the AC fault status, battery state of charge, or power supply condition.

CAUTION - Always check for AC presence with a volt meter before servicing

5.2.2.1.2 DC OUT

This LED illuminates when DC voltage is available at the DC+/DC- terminals.

RMMV Series Installation Instructions

7/13/2009, 10:26:56 AM

52-391 Rev A.02

Page 13 of 20

AlarmSaf

65A Industrial Way, Wilmington, MA 01887 978 658 6717 www.alarmsaf.com

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 19 20

Kommentare zu diesen Handbüchern

Keine Kommentare

Alarm SAF RMBE Series Bedienerhandbuch Seite 13

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Elektrische Gehäuse Alarm SAF RMBE Series